CJC 1295 Dac will not reconstitute

[Cratos]

I tried reconstituting CJC 1295 Dac with Bacteriostatic Water both straight out of the refrigerator and it didn't dissolve (10mg 1ml water). I left it room out in the drawer for two hours and it's a little more dissolved. Since I added 2ml more and put it back in the fridge and next day it looks as it does in the photos. I doubt 1 more ml of water can fit in there but I am open to any suggestions. Is this batch screwed or is there something I can do to use it? This was in the first batch of peptides I ordered and the TB500 10mg was fine with 1ml water at room temp and bpc 5mg was also good with 1ml. Also, do the peptides and BA have to be room temp to properly mix?

 

[awm1981]

I tried reconstituting CJC 1295 Dac with Bacteriostatic Water both straight out of the refrigerator and it didn't dissolve (10mg 1ml water). I left it room out in the drawer for two hours and it's a little more dissolved. Since I added 2ml more and put it back in the fridge and next day it looks as it does in the photos. I doubt 1 more ml of water can fit in there but I am open to any suggestions. Is this batch screwed or is there something I can do to use it? This was in the first batch of peptides I ordered and the TB500 10mg was fine with 1ml water at room temp and bpc 5mg was also good with 1ml. Also, do the peptides and BA have to be room temp to properly mix?


View attachment 11551View attachment 11552View attachment 11553

I keep mine in the freezer.

Then I reconstitute with 1ML of bac water. I roll it between my fingers till it all dissolves. Warmth from my fingers usually is good enough to help reconstitute.

 

[Cratos]

I keep mine in the freezer.

Then I reconstitute with 1ML of bac water. I roll it between my fingers till it all dissolves. Warmth from my fingers usually is good enough to help reconstitute.

1ml for 10mg work for you? So you add the water straigth out of freezer and roll for a few minutes until it's dissolved?

 

[awm1981]

1ml for 10mg work for you? So you add the water straigth out of freezer and roll for a few minutes until it's dissolved?

So my vials from PSL are 2mg.

10mg you will need more sorry i didnt see that. Yea I will add straight from the freezer, let it run slowly down the sides, rollin in my hands or fingers for a minute or 2 and then inject.

As long as the chunks are all dissolved you are good to go.

 

[Cratos]

So my vials from PSL are 2mg.

10mg you will need more sorry i didnt see that. Yea I will add straight from the freezer, let it run slowly down the sides, rollin in my hands or fingers for a minute or 2 and then inject.

As long as the chunks are all dissolved you are good to go.

so even if it's cloudy its ok to use? Just potency is lower since it isnt all dissolved?

 

[awm1981]

so even if it's cloudy its ok to use? Just potency is lower since it isnt all dissolved?

It would only not be as potent if you were not able to draw up. If its cloudy but you can still draw in all of the liquid it shouldnt be less potent?

If, when you daw up all the bac water, there is a cloudy film left over then yes would be lower potency but could try and reconstitute with more bac water to get it all out.

 

[Chemically Enhanced]

All my CJC (from 2 different companies) were 2mg. Some peptides dissolve fine in small volume of water (10mg MT2 can dissolve on 0.5ml) and some peptides need more volume (5mg HGH frag needs at least 2ml). I've never seen CJC in Canada in more than 5mg per vial. And I've never seen any peptide getting cloudy. There may be undissolved chunks but I've never seen it cloudy. Not even sure what to do say other than contact your supplier and demand an explanation.

Sent from an alien spaceship using Tapatalk

 

[Mobster]

The guys have you covered.

 

[stevesmi]

which company?

 

[Cratos]

All my CJC (from 2 different companies) were 2mg. Some peptides dissolve fine in small volume of water (10mg MT2 can dissolve on 0.5ml) and some peptides need more volume (5mg HGH frag needs at least 2ml). I've never seen CJC in Canada in more than 5mg per vial. And I've never seen any peptide getting cloudy. There may be undissolved chunks but I've never seen it cloudy. Not even sure what to do say other than contact your supplier and demand an explanation.

Sent from an alien spaceship using Tapatalk

Will do. Thanks.

- - - Updated - - -

which company?

****************

First order with them.

 

[muskate]

That looks sketchy as shit. I would not put that into my body dude.

CJC should mix instantly with water. There are some sort of weird impurities in those vials

 

[Masonic Bodybuilder]

Honestly I don't have a definitive answer but I would always be on the safe side so maybe don't use it. You can always contact your source directly.