Crystals in test bottle

[Maxim0]

Hey guys I've heard about this many times but have never dealt with it myself. What's the best procedure for taking care of this? Getting all sorts of answers when I google it

 

[Bigjayp]

I have had some crystallized gear in the past. Old cat named BL was trying to make high dose gear, but it kept crashing and therefore crystallizing. Do you know why yours is crystallizing?

What I did:
1. get a pot 2. fill with water low enough that you can put the bottle down in the water and it not cover the top of the bottle. 3. Boil the water 4. Remove the pot from heat source 5. let the boiling stop and get some of that hot hot heat off of it. 6. get a clean needle and put it in the top of your bottle so it can vent. 7. get some tongs and put the bottle in the hot water. (not your open pin, you don't want water in your gear) 8. Occasionally pull it out and swirl it around. 9. Rinse and repeat until the crystals are all gone. 10. Once it is cool enough to shoot remove the vent pin 11. Clean your bottle with alcohol, get a new pin, draw it, shoot it.

Good-luck!

 

[muskate]

The easiest way is to boil some hot water and pour it in a bowl. Place the vial inside the the bowl of hot water so hot water rises to approximately haft way up the side of the vial. Let it sit there for 2-3 minutes. Shake the vial vigorously for 20-30 seconds after that and the steroid compound should be re-suspended in the oil.

If that doesn't work, put the vial in your oven and pre-heat the oven to 250-300 degrees Fahrenheit.

 

[jon38]

Ive used both of those meathods and hairdryers pretty much just get it hot enough without over heating it and shake swirl it will resuspend in my experiance though gear crashes 2 ways if it gets too cold then when you do this its good too go but when its got a ton of gear in it and keeps crashing you have too do this every other day or so it will crash ober and over its still good just annoying

 

[Bigjayp]

Ive used both of those meathods and hairdryers pretty much just get it hot enough without over heating it and shake swirl it will resuspend in my experiance though gear crashes 2 ways if it gets too cold then when you do this its good too go but when its got a ton of gear in it and keeps crashing you have too do this every other day or so it will crash ober and over its still good just annoying

Never tried the hair drying, but it sounds much easier.... Thanks for throwing that out there! Yea, it is annoying lol....

 

[jon38]

Just make sure it goes clear no crystals before you pin or you may get some nasty pip . still might crash in you i would stick toonthe glutes no delt pins with that

 

[Bad Juju]

you can oven at 180 degrees man. it won't melt the stopper. just take the flip top off. if it crashes again just use a hair dryer from that point on to heat up and clear before you inject. Good thing is it means the gear is overdosed at least lol

- - - Updated - - -

6. get a clean needle and put it in the top of your bottle so it can vent.

this is a myth. gear will not pop the bottle. there is no need to expose the gear to "vent"

 

[LevButlerov]

As it has already been mentioned twice above, the best thing to do is to heat up the gear and shake it, so that the crystals will get dissolved. Not a big deal - happens from time to time.

 

[stevesmi]

I onced warmed a vial in the oven but forgot about it. the glass ended up exploding and the gear was all over the place.. it was a mess.

 

[cybrsage]

As a note, if you have test suspension (test in water), you WILL have crystals forming - no way around it.

 

[Bad Juju]

I onced warmed a vial in the oven but forgot about it. the glass ended up exploding and the gear was all over the place.. it was a mess.

thats the first I've ever heard of that. how hot did it get lol